日本黄页网站-日本黄页网-日本黄页视频-日本黄页免费大片在线观看-国产免费网址-国产免费网站看v片元遮挡

EN CN

Common problems

Home / Common problems

Working principle and method of CNC bending machine


Update date:2017-11-11 Browse:4545


This kind of CNC bending machine tool for bending the thin plate. , including the CNC bending machine mould bracket, workbench and clamping plate, when used by a conductor to coil electricity, after electrify produces gravity to clamp, so as to realize the clamping plate between the pressure plate and the base. Because of the electric magnetic clamping, it can be used to make a variety of workpiece requirements, and it can be processed to the workpiece of the side wall, and it is very simple to operate. According to the ordinary hydraulic CNC bending machine mold processing Q235 sheet materials to do a brief introduction:

1. First, turn on the power, turn on the switch on the control panel, and then start the oil pump, so that you can hear the oil pump turning. (the machine does not move at this point)

2. Stroke adjustment, use must pay attention to adjust the itinerary, must test before bending. It must be ensured that there is a thick gap between the top and bottom. Otherwise, the die machine will be damaged. The adjustment of stroke also has electric quick adjustment.

3. Select the groove of the groove and choose the slot with a thickness of 8 times the width of the plate. If the sheet that bends 4mm, need to choose the slot of 32 or so.

4. After adjustment of the back material, it is generally electric quick adjustment and manual fine tuning, which is the same as the shearing machine.

5. Step down the pedal switch and start bending. The CNC bending machine is different from the cutting machine. It can be released at any time, loosen its legs and stop, and continue to slide. Plastic CNC bending machine tooling, plastic folding machine, plastic board CNC bending machine mold, plastic plate bending plastic plate bending directly, without joining together, without slot, don't need a electrode, the Angle of the appearance it hold water, it will be hand soldered into a fully automatic machine operation, improve the quality, improve the work efficiency, reduce the labor cost, shorten the production cycle of products. Fully automatic plastic folding Angle machine is a fully automatic mechanical equipment. According to the principle of plastic sheet heating and soft melting welding, it is suitable for all kinds of thermoplastic materials. The speed is quick, the corner treatment surface is beautiful, the intensity is high. Hydraulic shearing machine is divided into pendulum and brake type. Pendulum is due to the arc, activated carbon and arc blade production is very difficult, is commonly made mat iron blades after compensation, so of clearance is not accurate, cut out of sheet metal is not very ideal. Because it is arc movement, the rectangular blade can't make it, and acute Angle should make it, so the force of the blade is not ideal, the blade damage is severe. A pendulum shear domestic representative for tianshui machine tool plant and punching and shearing machine tool plant. Brake type hydraulic shearing machine has overcome the above all problems. But at present domestic manufacturer can do brake type shearing machine is not much. Relative to the shearing machine, CNC bending machine tooling technology content to be a little higher. At present domestic common G shape and F, F shape should be domestic traditional product, its use is built-in adjustable mechanical stop positioning, because it is built-in the partial load resistance is weak, so have the Yellowstone in the early days of CNC bending machine mold has a balance valve, but also because of the hydraulic, too multifarious, brings to the late maintenance and stability is very serious problem. The latter is G type, after the F type model to improve its use outside skateboarding mechanical positioning, type F the more simple, more convenient debugging, even in the case of both sides Angle difference under can also be released from amateurs to add gasket to problem.

Now there are H CNC bending machine mold, the structure is different than before two kinds of it as a lever type structure, which is generally used in large tonnage CNC bending machine tooling, through the lever principle, the force amplification. At the same time it USES electric \ \ \ \ fluid combined with the location of the control, in the same tonnage of CNC bending machine mold especially high performance-price ratio. But domestic manufacturer of such models, numerical control hydraulic sheet metal numerical control bending machine mould bed main features: WC67K CNC bending machine tooling, USES the steel plate welded structure, vibration aging eliminate stress, machine tool has very good rigidity and stability, and the whole frame rigidity, stable, safe and reliable, easy to operate, through the CNC bending machine mould numerical control system and hydraulic system of the coordinated control, to achieve the ideal effect of bending.

Previous: Introduction and operation of the shears    Next : The prebending function is important to the roll plate machine return

Contact us

  • Address:Industrial concentration
    zone (renmin road), libao town,
    haian county, jiangsu province
  • MB: 13584710666
  • TEL: 0513-88280988
  • FAX: 0513-88283387
  • E-mail: jslx@jslxzg.com
日本AAAAAAAAA级作爱片在线观看 国产69精品久久久久熟女白洁老汉出租屋 | 欧一美一婬一伦一区二区三区麻婆 | 91精品国产高清一区二区三密臀 | 精品国产乱码一区二区三区在线观看 | 一本无码人妻一区二区 | 欧美精品少妇猛烈进入A片免费看 | 亚洲无码黄色视频在线 | 无码人妻一区二区三区免水牛视频 | 午夜影院普通用户免费视看 | 国产酒店A片偷拍 | 亚洲欧洲精品毛AA久久A就毛 | 国产精品无码一二三区色情游戏 | 亚洲电影中文字幕 | 国产情侣xxxxx | 亚洲精品成人A片动漫 | 国产熟妇婬乱1一15集电视剧 | 午夜视频免费观看 | 免费亲子乱婬一级A片 | 亚洲Av麻豆一区二区一二区 | 亚洲AV乱码一区二区三区女同 | 久久精品噜噜噜成人88Aⅴ | 少女视频哔哩哔哩高清播放 | 亚洲色图小说图片视频 | 亚洲无码成人在线观看 | 久久精品无码精品三级 | aaa级毛片在线观看 美女破处视频在线观看 | 性欧美 潮喷偷拍 | 亚洲国产精品无码久久久五月天 | WWW.17C嫩嫩草色视频蜜桃 | 亚洲AV无码一区二区三区在线 | 欧美寡妇一级A片免费视频 99人妻碰碰碰久久久禁片 | 中国少妇自慰成人A片 | 国产精品日韩亚洲精品 | 伦精品午夜一级婬片A片 | 91亚洲人午夜一线二香蕉吧在线 | 女人自慰网站在线观看 | 少妇高潮惨叫久久麻豆传 | 性行为视频一级录像免费 | 亚洲精品乱码久久久久久按摩观 | 国产真实老熟女无套内射 | 亚洲熟女AV网址 |